page_banner

Rotary Damper Torque Calculation

As we mentioned earlier, a rotary damper works by providing resistance against movement, helping to slow down and control the motion of a product.

The amount of this resistance is very important. For a rotary damper, this rotational resistance is expressed as damping torque.

Part 1. Basic Torque Logic

1. Why Do We Need to Calculate Torque?

Before selecting a rotary damper, we first need to know approximately how much torque the application requires.

Rotary dampers are available in very different torque ranges. Some are designed for very small loads, while others are intended for much larger mechanisms.

So the main purpose of torque calculation is to determine the approximate torque range we should look at.

For example, if the calculated required torque is about 2 N·m, we should start by looking at dampers around the 2 N·m range, rather than products rated at 0.2 N·m or 10 N·m.

At this stage, we are only narrowing down the torque range. The exact damper model will be determined later.

2. Basic Torque Principle

The basic relationship is:

Torque = Force × Distance

In simple terms, torque depends mainly on two things:

How large is the force?

and

How far is that force from the pivot?

A seesaw is an easy way to understand this.

Basic Torque Principle

Imagine two people sitting on opposite sides of a seesaw.

The center of the seesaw is the pivot.

The weight of each person creates a force.

The distance between each person and the center pivot is the distance.

If two people have the same weight, but one person sits farther from the center, that person produces more torque.

If one person is heavier but sits closer to the center, the two sides may still balance.

The same principle applies to a lid.

A heavier lid usually produces more torque.

But even with the same weight, a lid whose center of gravity is farther from the pivot will also produce more torque.

So when calculating rotary damper torque, we are always trying to answer two basic questions:

What is the force?

What is the effective distance from that force to the pivot?

The calculation methods below are simply different ways of finding these two values.

3. Which Position Should Be Used for the Calculation?

Before calculating torque, we also need to know which position of the product we are calculating.

For a simple lid that rotates under gravity, the torque changes as the lid moves.

When the lid is close to vertical, gravity has relatively little rotational effect around the pivot.

As the lid moves toward the horizontal position, the effective distance through which gravity acts around the pivot becomes larger, so the torque also increases.

Near the horizontal position, the gravity torque is usually at its maximum.

So, for a simple gravity-driven lid, the horizontal or near-horizontal position is commonly used when estimating the maximum or reference torque for initial damper selection.

This does not mean that the torque remains the same throughout the movement.

It only gives us a useful maximum or reference value.

How the torque changes during the full movement is a separate question, which we discuss in Torque Curve Matching.

 

Part 2. Common Torque Calculation Methods

For a simple gravity-driven rotating product, there are two common ways to obtain the force used in the torque calculation.

The difference is simple:

Method 1 measures the force directly.

Method 2 calculates the force from the product weight.

Both methods are based on the same principle:

Torque = Force × Distance

1. Method 1: Calculate from Lifting Force

If the lifting force can be measured directly, torque can be calculated from:

Torque = Lifting Force × Distance from Pivot

Here, the lifting force is the force needed to slowly support or lift the product at the measurement point.

The distance is the distance from the pivot to the point where the force is measured.

For example, suppose a lid is placed near the horizontal position.

The lifting force measured at the end of the lid is:

2 N

The distance from the pivot to the measurement point is:

0.5 m

Then:

Torque = 2 N × 0.5 m

Torque = 1 N·m

Calculate from Lifting Force

The important point is that the force should be measured slowly.

If the lid is moved quickly, acceleration and inertia can affect the reading.

The purpose here is to estimate the torque created by the mechanism, not the force required to accelerate it rapidly.

So this method can be understood simply as:

Measure the force, measure the distance, and calculate the torque.

2. Method 2: Calculate from Product Weight and Center of Gravity

If the product weight and center of gravity are known, the torque can also be calculated without measuring lifting force directly.

First, the product mass is converted into gravitational force.

Then this force is multiplied by the distance from the pivot to the center of gravity.

For a simple horizontal lid:

Torque = m × g × L

where:

m = product mass
g = gravitational acceleration
L = distance from the pivot to the center of gravity

For example, suppose:

Product mass = 2 kg

Distance from pivot to center of gravity = 0.2 m

The gravitational force is approximately:

2 × 9.81 = 19.62 N

So:

Torque = 19.62 × 0.2

Torque ≈ 3.92 N·m

The important point here is the center of gravity.

Calculate from Product Weight and Center of Gravity

The center of gravity is the point where the product’s weight can be considered to act. Its position depends on the product’s shape and weight distribution.

For a simple product with a regular shape and uniform weight distribution, the center of gravity is usually close to its geometric center.

For a more complex product with an irregular shape or uneven weight distribution, the center of gravity may shift toward the heavier side. In this case, CAD data or actual product measurements can be used to determine its position.

The distance used in the torque calculation is therefore not automatically the full length of the lid.

It is the distance from the pivot to the center of gravity.

So Method 2 can be understood simply as:

Calculate the gravitational force, find where that force acts, measure the distance from the pivot to that point, and then calculate the torque.

Method 1 and Method 2 are therefore not based on two different physical principles.

They are simply two different ways of obtaining the force used in the same torque calculation.

 

Part 3. Torque Calculation for More Complex Mechanisms

The two methods above work well for simple products that rotate around a pivot under gravity.

But many rotary damper applications are not that simple.

Some products move in a straight line.

Some use gears between the product and the damper.

Others are driven by springs or by several forces at the same time.

The same basic torque principle still applies, but we need to look more carefully at how the force is transferred to the rotary damper.

1. Torque Calculation for Linear Motion with Rack and Pinion

A rotary damper can also control a product that moves in a straight line.

A common mechanism is:

Linear Movement → Rack → Pinion → Rotary Damper

Torque Calculation for Linear Motion with Rack and Pinion

The product itself is moving linearly, but the rack turns the pinion, and the pinion rotates the damper.

In this case, the linear force must be converted into rotary torque.

The basic relationship is:

Torque = Linear Force × Pinion Radius

For example, if a load moves vertically downward under its own weight, the driving force can be estimated from:

F = m × g

Then:

Torque = m × g × r

where r is the effective radius of the pinion.

Again, the basic principle has not changed.

It is still:

Force × Distance

The difference is that the relevant distance is now the pinion radius, rather than the distance from a lid pivot to its center of gravity.

2. How Gear Ratio Changes the Torque at the Damper

Sometimes the rotary damper is not mounted directly on the product pivot.

Instead, the movement is transmitted through gears.

For example:

Product Shaft → Gear → Damper Gear → Rotary Damper

In this case:

Product-side torque does not necessarily equal damper-side torque.

The gear ratio changes the torque seen by the damper.

For example, a larger gear on the product side driving a smaller gear on the damper can make the damper rotate faster while reducing the torque required at the damper shaft.

This can allow a smaller-torque damper to control a mechanism with a larger product-side torque.

However, there is another effect:

Changing the gear ratio also changes the rotational speed of the damper.

This is important because rotary damper torque is also affected by rotational speed.

So when gears are used, both torque ratio and speed ratio need to be considered.

3. Spring-Driven and Combined Mechanisms

Not every product is driven only by gravity.

Some products are opened or returned by a spring.

Others may be affected by:

gravity + spring force

Spring-Driven and Combined Mechanisms

or by linkages and other mechanisms.

In these cases, the ordinary gravity-lid calculation cannot simply be used without checking the actual driving force.

For example, a spring may provide a strong force at the beginning of the movement and a weaker force later as it is released.

Gravity may be helping the movement in one position but opposing it in another.

So the real question becomes:

What forces are driving the product at each position, and how are those forces transferred to the damper?

For these mechanisms, the maximum torque may not occur at the horizontal position.

The actual force and transmission relationship need to be considered.

 

Part 4. How to Use the Calculated Torque

What Does the Calculated Torque Actually Mean?

Suppose the calculation gives:

Maximum / Reference Torque ≈ 2 N·m

Now we know the approximate torque range we should look at.

But this still does not tell us exactly which rotary damper to choose.

There may be many rotary dampers around the 2 N·m range.

They may belong to different types, such as disk dampers, vane dampers, gear dampers, or barrel dampers. Even within the same damper series, several torque ratings and models may be available.

The next step is to filter these candidates by basic requirements such as the damping direction, whether one-way or two-way damping is needed, and the working angle.

Even after these requirements are confirmed, there may still be several suitable dampers.

In some cases, a damper may meet the required torque, damping direction, and working angle, but the actual movement of the product is still not satisfactory after installation.

Why?

Because a single maximum torque value only tells us the torque level at a reference point. It does not describe what happens throughout the entire movement.

The product torque can change with position.

The damper torque can also change with rotational speed and temperature.

This is why the next step is to look at Torque Curve Matching and understand whether the product’s Gravity Effect Curve and the damper’s Damping Torque Curve work well together throughout the movement.

So torque calculation helps us find the right torque range, but it is only one step in rotary damper selection.